6 of 18
888-24-227-G-00 rev. B • 07/13
Brake Release
Use Drill Bit #21,
Ø
0.19” (4.8 mm)
to drill these 9 holes
3/8” (9.5 mm) deep.
Use Drill Bit #21,
Ø
0.19” (4.8 mm)
to drill these 8 holes
3/8” (9.5 mm) deep.
Use Drill Bit #46,
Ø
0.081” (2mm)
to drill these 3 holes
0.24” (6 mm) deep.
Center Point of Base Brackets
TIPPING HAZARD!
Center Worksurface from Side-to-Side Across Base Brackets.
Failure to follow these instructions may make this product unstable
and may result in equipment damage and/or personal injury.
Brake Release
Use Drill Bit #21,
Ø
0.19” (4.8 mm)
to drill these 9 holes
3/8” (9.5 mm) deep.
Use Drill Bit #21,
Ø
0.19” (4.8 mm)
to drill these 8 holes
3/8” (9.5 mm) deep.
Use Drill Bit #46,
Ø
0.081” (2mm)
to drill these 3 holes
0.24” (6 mm) deep.
Center Point of Base Brackets
TIPPING HAZARD!
Center Worksurface from Side-to-Side Across Base Brackets.
Failure to follow these instructions may make this product u
nstable
and may result in equipment damage and/or personal injury.
Brake Release
Use Drill Bit #21,
Ø
0.19” (4.8 mm)
to drill these 9 holes
3/8” (9.5 mm) deep.
Use Drill Bit #21,
Ø
0.19” (4.8 mm)
to drill these 8 holes
3/8” (9.5 mm) deep.
Use Drill Bit #46,
Ø
0.081” (2mm)
to drill these 3 holes
0.24” (6 mm) deep.
Center Point of Base Brackets
TIPPING HAZARD!
Center Worksurface from Side-to-Side Across Base Brackets.
Failure to follow these instructions may make this product u
nstable
and may result in equipment damage and/or personal inju
ry.
1
X
Depth of
Worksurface
23.50 - 24.25”----0.25”
24.25 - 25.00”----0.75”
25.00 - 25.75”----1.25”
25.75 - 26.50”----1.75”
26.50 - 27.25”----2.25”
27.25 - 28.00”----2.75”
28.00 - 28.75”----3.25”
28.75 - 29.50”----3.75”
29.50 - 30.25”----4.25”
X
Depth of
Worksurface
597 - 616 mm ---6 mm
616 - 635 mm ---19 mm
635 - 654 mm ---32 mm
654 - 673 mm ---44 mm
673 - 692 mm ---57 mm
692 - 711 mm ---70 mm
711 - 730 mm ---83 mm
730 - 749 mm ---95 mm
749 - 768 mm ---108 mm
2.1262.126
X
Back of Base Bracket
4.25” (108 mm)
3.75” (95 mm)
3.25” (83 mm)
2.75” (70 mm)
2.25” (57 mm)
1.75” (44 mm)
1.25” (32 mm)
0.75” (19 mm)
0.25” (6 mm)
Align
REAR
Edge of Worksurface
X
distance
from the back of the Base Brackets.
See table for value of
X
based on the depth of
your worksurface.
Place the worksurface on a clean oor with the top side facing down.
Center Template
Side-to-Side on
worksurface.
Align REAR Edge of Worksurface X distance from the back of the Base Brackets.
See table for value of X based on the depth of your worksurface.
Depth of
Your Worksurface
Tape Template in place.
Set-up Steps
(12 paginas)
(17 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales